Sink Drains

Публикувано от: ремонт  :  Категория: Строител

A stopped sink drain isn’t just an inconvenience; it can sometimes be an emergency.

It’s always best to prevent clogs before they happen. Be alert to the warning sign of a sluggish drain it’s easier to open a drain that’s slowing down than one that’s stopped completely.When it’s too late for preventive medicine, a dose of scalding waterespecially effective against grease buildups may be treatment enough.

If not, it could be that something foreign a button, coin, or small utensil has slipped down the drain. To check, remove and thoroughly clean the sink pop-up stopper or strainer.

Често, a clog will be close to the sink. You can determine this by checking the other drains in your home. If more than one won’t clear, something is stuck in the main drain. Otherwise, you’re probably dealing with a clog in the sink trap or drainpipe. The most effective way to clear a clog is with a snake (виж обърната страница). You can try using a plunger or a chemical drain cleaner first; in any case, pay special attention to the cautions on these pages before you begin work.

Clearing Drains with a Plunger

What’s the first reaction to a clog? Reach for the plumber’s helper the plunger. The plunger is a good drain-clearing tool, but it often fails to work because it’s incorrectly used. Don’t make the typical mistake of pumping up and down two or three times, expecting the water to whoosh down the drain.

Though no great expertise is needed to use this simple tool, here are a few tips to guide you:

Choose a plunger with a suction cup large enough to cover the drain opening completely as shown in the drawing at right.

Fill the clogged fixture with enough water to cover the plunger cup.

Coat the rim of the plunger cup with petroleum jelly to ensure a tight seal.

Block off all other outlets (the over-flow, second drain in a double sink, adjacent fixtures) with wet rags.

Insert the plunger into the water at an angle so no air remains trapped under it,

Use 15 to 20 forceful strokes, holding the plunger upright and pumping vigorously

Repeat the plunging two or three times before giving up.

Using Chemical Drain Cleaners

Though routine use of chemical drain cleaners to prevent clogs may eventually damage your pipes (виждам “Pre-venting Drain Clogs, these cleaners can be helpful in opening clogged drains. If water is draining somewhat but plunging has failed to open the drain completely, you may want to try using a drain cleaner.

Whenever you use chemicals, do so with caution and in a well-ventilated room. Be sure to take these precautions:

Never use a plunger if a chemical cleaner is present in the drain; you risk splashing caustic water on your-self.

Wear rubber gloves to prevent the chemical from burning your skin.

Avoid splashing the cleaner.

Don’t use a chemical cleaner if the blockage is total, especially if the

fixture is filled with water. It won’t clear the blockage, and you’ll face

another problem how to get rid of the caustic water.

Never use a chemical cleaner in a garbage disposer.

Read labels and match cleaners with clogs. Alkalis cut grease; acids

dissolve soap and hair.

Don’t mix chemicals. Mixing an acid and an alkali cleaner can cause an explosion.

Don’t look down the drain after pouring in a chemical. The solution

often boils up and gives off toxic fumes.

към : E-book Home repair

Pop-up Stoppers

Публикувано от: ремонт  :  Категория: Строител

As its name implies, a pop-up stopper moves up or down to open or close the drain. The primary stopper problem is a bad fit between the stopper and the sink or tub.

When a stopper doesn’t seat properly, you need to remove and inspect it. Some sink stoppers sit atop the pivot rod and simply lift out; others require a slight twist to free them because a slot on the body hooks them to the rod. Still others are attached to the pivot rod.

To remove a tub stopper, pull it out along with the rocker arm. (They should come out readily, since the striker spring rests unattached on the rocker arm.) Clean the stopper of hair and debris. If there’s a rubber seal, pry it off and check for damage. Slip on a new one if needed. Also make sure the flange is tightly seated and in good shape.

If a sink stopper still doesn’t seat properly adjust the clevis screw, pivot rod, or retaining nut (виж по-долу). If a tub stopper doesn’t fit after cleaning, remove the overflow plate and pull the entire lever assembly out through the overflow. Loosen the adjusting nuts; slide the middle link up the striker rod. Lower the link for a sluggish drain.

Sink Pop-up Assembly

Sink Pop-up Assembly

Tub Pop-up Assembly

Tub Pop-up Assembly

Adjusting a Sink Pop-up

Adjusting a Sink Pop-upAdjusting a Sink Pop-upAdjusting a Sink Pop-up

към : E-book Home repair

Laptop Keyboards

Публикувано от: ремонт  :  Категория: Входни устройства

Laptop keyboards are essential to the portability of a laptop. Imagine trying to tote a laptop or use one on a plane if you have to use a separate keyboard. The most common reason to have to replace a laptop keyboard is if liquid spills on it, but the rest of the machine still works. Laptops vary widely in how to remove the keyboard, and laptop manufacturers vary widely in providing such information. например, IBM? makes detailed service instructions for its ThinkPad? laptops available on its Web page (ibm.com), while many other companies do not make this information available on the Web. There are two common ways to remove a laptop keyboard. One is, with the power off and battery removed, to look for a removable panel around the keyboard. There might be a screw or two holding it in place (see Figure 9.8).

Click To expand
Figure 9.8: The removable panel type of laptop keyboard removal.

Remove the screw(С) and then the panel. You might then see a screw holding in the keyboard. Remove the screw and lift the keyboard slightly. Look underneath to see where the ribbon cable is, as shown in Figure 9.9. Make certain not to stress the ribbon cable as you lift the keyboard out of the way. The other method some manufacturers use is to look at the bottom of the laptop and remove any screws marked with “K” (see Figure 9.10). Then, gently lift the keyboard out following the previous instructions to prevent damage to the ribbon cable.

Click To expand
Figure 9.9: Treat the ribbon cable with care.
Click To expand
Figure 9.10: The K screw.
Забележка If liquid has spilled on a laptop, do not attempt to power it on until you or a technician experienced in portable computers has determined that there is no liquid present anywhere in the system. See Chapter 11 for more information on attempting to rescue a laptop that has been exposed to liquid.

към : Книга-компютър ремонт и поддръжка: А Практическо ръководство